Pharmaceutical & Medical

The metallic effect is created by hand during installation, so the pattern, depth and distribution can't be reproduced exactly from a photo. Lighting in your space also changes how it reads. We show physical samples and photos of our own past floors, agree the colour and general movement you're after, and explain where variation will come from.

Metallic finishes are high-gloss and smooth, which makes scratches, grit and salt residue more visible than on a textured flake floor. In a garage that sees daily winter traffic, that can mean more maintenance. For show garages and less-used spaces, they're a strong choice. A UV-stable topcoat matters where sunlight reaches the floor.

Cottage garages and boathouses near Georgian Bay and Lake Simcoe tend to sit cold and damp through winter and get heavy use in summer. Moisture and condensation are bigger factors than in a heated home, so testing matters. We schedule installation in the months when conditions allow and specify a system for the humidity and use, including traction where floors are often wet.

Through winter, salt dries into a white film. In spring, sweep, rinse with water, and wash with a neutral cleaner or one recommended for your coating, then rinse again. Avoid acidic cleaners and abrasive scrubbing pads that can dull the finish. Doing a quick rinse during winter thaws, where practical, stops the build-up. We hand over care instructions with every floor.

Hot tire pickup happens when a warm tire softens and grips a coating, then pulls it away as it cools and the car moves. It's most common on thin coatings over poorly prepared concrete, or on floors driven on before they've fully cured. Mechanical preparation for a proper bond, a coating system with suitable thickness, and waiting for the stated vehicle cure time are the main defences.

The main variables are how much repair the slab needs, how many layers the system has, and how long each layer takes to cure at the conditions on the day. A garage in good condition with a fast-curing system is quicker than one needing salt-damage repair first. We give you a written schedule with the quote, including when you can walk on it and when you can park on it.

Most garage and basement cracks are shrinkage cracks from the concrete curing, and they're routinely treated before coating. We're a flooring contractor, not engineers, so we won't tell you a crack is structurally safe. Signs worth an engineer's opinion include a crack that's growing, one side sitting higher than the other, doors that have started sticking, or visible settlement.

After the snow is gone, wash the floor and look closely at the first few feet inside the door and the wheel paths. Flaking and pitting suggest salt and freeze-thaw damage. New or widening cracks are worth noting. White residue is dried salt that should be washed off. If you're considering a coating, photographs of these areas help us give you a better idea of what the repair will involve before we visit.

Unheated garage work can't start until conditions meet the product's requirements, which in Clearview and the surrounding area usually means mid-to-late spring. Because every contractor starts at the same time, the first weeks book up early. Booking in March or April gets your slab assessed and your job scheduled, so it's installed as soon as conditions allow.

A garage heated to a steady temperature can meet a product's requirements in the middle of winter. What trips it up is the door: opening it lets cold air across a curing floor and can pull the slab temperature down quickly. We confirm the space can hold temperature before booking, check readings on the day, and agree when the door stays shut. Ventilation still has to be managed during application.

Every product's technical data sheet gives a cure time for light foot traffic and a longer one for vehicle traffic, and both lengthen as temperature drops. Polyaspartic topcoats generally return to service faster than conventional epoxy systems, which is one reason they're used in Ontario garages. Hot tires on a floor that hasn't fully cured can mark it, so we give you a specific time for your floor on the day, based on the product and conditions, rather than a general number.

Scaling is loss of the top layer of concrete, usually in patches, and is commonly linked to freeze-thaw exposure with de-icing salts. Cracking is a break through the slab, which can come from shrinkage as the concrete cured, settlement, or movement. Most garage cracks are shrinkage cracks and can be treated before coating. Cracks that are widening, uneven across the break, or accompanied by settlement are a different matter, and a structural engineer should look at those before any coating decision is made.

The first few feet inside a garage door take the most punishment in an Ontario winter: snow falls off the car, melts, pools with dissolved salt, and freezes again when the door opens. That zone also has the widest temperature swings. Surface scaling — thin flakes coming away — often starts there, and it can also point to a weaker surface layer from how the slab was originally finished. We assess it before recommending anything, because the fix depends on how deep the damage runs.

Salt damage typically shows as scaling, pitting and spalled edges, and the first job is to find out how deep it goes. We grind until we reach sound concrete, then rebuild the damaged areas with a compatible repair material and grind them flush before any coating goes down. Coating directly over scaling usually fails, because the coating is only as strong as the layer it's bonded to. If the damage is deep or structural, repair alone may not be the answer, and we'll say so.

Any smooth, sealed surface becomes more slippery when wet, and an Ontario garage is wet for much of the winter. A full-flake broadcast has more surface texture than a solid colour, and fine aggregate can be incorporated into the topcoat where the product's data supports it to add traction. The trade-off is cleanability: the more texture, the more effort to mop. We usually suggest more texture in the zone just inside the door, where meltwater lands, and less elsewhere.

Two garages of the same size can price quite differently. A newer slab in good condition needs grinding and coating; an older one may need salt-damage repair, crack treatment or removal of a previous coating first, and those steps are where most of the variation comes from. The system matters too — a full-flake broadcast with a clear topcoat is a different build from a single solid colour. We assess the slab before quoting, then give a written price in Canadian dollars with HST shown separately and nothing mandatory left out.

Every coating system has a technical data sheet that sets a minimum surface and air temperature and a required margin above the dew point, during application and through the cure. In an unheated Innisfil garage, those conditions usually stop being reliable as fall nights cool, and a floor applied outside them may not bond or cure properly. We schedule against the readings on the day rather than the calendar. A heated garage that can hold stable conditions before, during and after installation can be done through winter.

No. We use UV-stable topcoats that resist yellowing and keep the colour consistent for years.

No. We never install over damaged concrete. Full surface restoration and crack repair are part of our preparation process, because a coating is only as good as the slab beneath it.

You can usually walk on the floor after 24 hours and park vehicles after 48–72 hours. Colder temperatures slow the cure, so your quote includes the exact return-to-service time for your system.

Epoxy bonds well and builds thickness, which makes it a good base layer. Many epoxies can yellow with sunlight exposure, which matters at a garage door. Polyaspartic topcoats are commonly chosen for UV stability and faster return to service, and many can be applied across a wider temperature range. A lot of Ontario garage systems use both. The right combination depends on the product data, your slab and how you use the garage.

Cars carry snow and slush loaded with de-icing salt into the garage, where it melts and pools, often near the door and under the wheels. Bare concrete is porous and absorbs that water. When temperatures swing around freezing, moisture in the surface expands and contracts, and the combination with chlorides is a common cause of scaling — thin layers of the surface flaking away — and pitting. Chlorides that reach reinforcing steel in structural slabs can also contribute to corrosion. A sealed or coated surface limits how much reaches the concrete, which is the main reason Ontario garages are coated at all.

Yes. A newer slab is usually in better condition, but the surface of fresh concrete is closed and a coating will not bond into it as it is.

Grinding opens the surface so the system anchors into the slab rather than sitting on top of it.

Usually yes. Age by itself is not the problem — moisture coming up through the slab is, and a lot of older houses here were built without a barrier underneath.

We check the slab before quoting. If the reading is high we put a barrier down first; if it is clean, nothing extra is needed.

No, it comes up constantly and we plan for it. With the garage door open the floor counts as something the neighbors see, so the board usually wants to sign off on the color first.

We bring physical samples you can submit and schedule the install once you have approval, so the floor is never done twice.

Usually yes. Stains and old patches sit at the surface, and grinding takes that layer off before anything is applied.

What we check for underneath is moisture and structural cracking, since those decide the build rather than the appearance.

Not with a properly bonded system. Hot-tire pickup happens when a coating is thin, poorly bonded or rolled on over unprepared concrete.

We grind rather than acid-etch, so the coating anchors into the slab instead of resting on top of it.

It comes off. A new system is only as sound as whatever it sits on, and putting fresh material over a failing one simply repeats the failure a year later.

We grind the old coating away mechanically, then assess the concrete underneath on its own condition.

Yes. Cracks, chipped edges and failed patches are repaired as part of the preparation, not treated as an extra afterwards.

A coating does not bridge a moving crack on its own, so the repair has to happen first if the finish is going to stay flat.

You can walk on it the next day. Vehicles need longer, because tires put far more stress on a fresh coating than feet do.

We give you the exact window before we start, so you can plan where the car goes in the meantime.

Yes, the floor has to be completely clear before we start — including shelving and anything fixed along the walls.

If moving heavy items is a problem, tell us when we quote and we will build it into the plan rather than leaving it to the morning of the job.

Yes. Polyaspartic systems are commonly installed in residential and commercial garages due to their resistance to hot tire transfer, vehicle traffic, humidity, abrasion and long-term UV exposure.

Yes. Properly installed epoxy flooring systems with industrial-grade topcoats are engineered to resist hot tire transfer and vehicle-related surface wear.

Epoxy flooring chemically bonds into the concrete substrate through mechanical preparation, creating a durable protective system. Standard paints primarily sit on the surface without providing the same adhesion strength or long-term durability.

Concrete coatings are engineered resin systems designed to mechanically bond into prepared concrete substrates. Standard paints primarily sit on the surface and do not provide the same adhesion strength, durability or long-term protection.